TC4钛合金材料采用金刚石砂轮磨削时的工艺参数优化

钛合金材料在航空器和发动机中的应用极为广泛,涡扇发动机中低压压气机静子叶片基本由钛合金材料制成,由于钛合金的磨削性能较差,对选用金刚石砂轮进行钛合金材料磨削时的主要工艺影响因素（如进给速度、磨抛深度等）进行了试验分析,优选出更适用于金刚石砂轮磨削钛合金的工艺参数,该参数不仅能够用于自研的双面仿形抛修设备,还可以对其他型号磨床磨削钛合金材料时的工艺参数选择提供指导。     

齿轮槽头型新型标准件安装工艺与试验研究

航空制造领域大量采用了如螺栓连接的标准件连接,随着新型飞机性能的提高,长寿命、高疲劳强度和高振动环境等指标对标准件的使用提出了更高的要求.本文通过开展齿轮槽头型新型标准件安装工艺与试验研究,一方面确定了该型标准件安装力矩等关键工艺参数及对复合材料的适用性,为其装机和使用提供理论依据及数据支持;另一方面,也对开展新型标准件安装工艺与试验的研究方法进行了有益的探索,对逐步形成一套完善的试验方法规范具有很好的指导作用.     

热塑性定型剂对干铺丝-RTM工艺及力学性能影响

为了研究热塑性定型剂的添加对干铺丝-树脂传递模塑（RTM）工艺的影响，采用PA-6作为热塑性定型剂，通过T-剥离确定定型剂的质量分数，结合试验和工艺仿真，研究了定型剂对预制体面内渗透率的影响，并对其充模过程进行工艺仿真和分析，在此基础上研究了定型剂对环氧复合材料制品层间性能及韧性的影响。渗透率试验和仿真结果表明:加入定型剂后，纤维预制体的沿纤维和垂直纤维的面内渗透率分别降低了55.5%和52.0%；工艺仿真结果与试验结果一致，不同渗透长度下的注胶时间偏差均小于10%。力学性能试验结果表明:加入热塑性定型剂可显著提升环氧树脂复合材料的韧性，Ⅰ型和Ⅱ型层间断裂韧性分别提高了89.3%和54.1%，冲击韧性提高了18.7%，复合材料的层间剪切强度降低了23.6%。      

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

进气道堵盖打开过程数值模拟

为获得整体式固冲发动机转级过程中进气道堵盖(包括入口堵盖与出口堵盖)打开过程的流动形态,建立了进气道二维模型,利用Fluent动网格技术和UDF方法,开展了进气道堵盖打开过程非稳态流场研究。结果表明,在入口堵盖打开前,进气道前端形成强烈的弓形激波;在入口打开、出口未开的过程中,沿进气道轴向各监测点压强呈现周期性变化,振荡频率为100 Hz左右,出口堵盖位置压强振荡幅值为0.53 MPa;在出口打开后,补燃室残余热量形成的压强峰导致进气道在短时间内无法起动,随着背压降低至小于进气道再起动反压,进气道完全起动。     

纺丝工艺对炭纤维缠绕复合材料强度转化率的影响

通过不同纺丝工艺的聚丙烯腈基炭纤维表面状态、NOL环及Φ150 mm容器的实验研究,分析了不同纺丝工艺对湿法缠绕复合材料聚丙烯腈基炭纤维强度转化率的影响。结果表明,干喷湿纺炭纤维比湿法纺丝Φ150 mm容器环向纤维强度转化率要高出11.9%~15.4%,湿法纺丝的炭纤维复合材料NOL环层间剪切强度要比干喷湿纺炭纤维复合材料高7.4~34.1 MPa。因此,干喷湿纺的炭纤维可应用于固体火箭发动机缠绕壳体、压力容器等主要承受拉伸应力的领域,可充分发挥其纤维强度;而湿法纺丝工艺制成的炭纤维与树脂基体结合紧密,利于载荷的传递,可应用于承受压缩剪切等复杂载荷的领域,从而发挥这两种纤维各自不同优势。     

Advances in fabrication of ceramic corundum abrasives based on sol–gel process

Corundum abrasives with good chemical stability can be fabricated into various free abrasives and bonded abrasive tools that are widely used in the precision machining of various parts. However, these abrasives cannot satisfy the machining requirements of difficult-to-machine materials with high hardness, high strength, and strong wearing resistance. Although superhard abrasives can machine the above-mentioned materials, their dressing and manufacturing costs are high. By contrast, ceramic corundum abrasives fabricated by sol–gel method is a cost-effective product between conventional and superhard abrasives. Ceramic corundum abrasives exhibit self-sharpening and high toughness. In this review, the optimization methods of ceramic corundum abrasive properties are introduced from three aspects: precursor synthesis, particle shaping, and sintering. Firstly, the functional mechanism of seeds and additives on the microstructural and mechanical properties of abrasives is analyzed. Specifically, seeds can reduce the phase transition temperature and improve fracture toughness. The grain size and uniformly dense structure can be controlled by applying an appropriate amount of multicomponent additives. Then, the urgent need of engineering application and machinability of special shape ceramic corundum abrasives is reviewed, and three methods of abrasive shaping are summarized. The micromold replication technique is highly advanced and can be used to prepare functional abrasives. Additionally, the influence of a new sintering method, namely, two-step sintering technique, on the microstructural and mechanical performance of ceramic corundum abrasives is summarized. Finally, the challenge and developmental trend of the optimization of ceramic corundum abrasives are prospected.     

耐高温异氰酸酯/ 环氧树脂固化历程与性能

以异氰酸酯为固化剂固化环氧树脂,通过比较不同固化条件下固化物结构的差异,研究了异氰酸酯与环氧树脂的反应历程;改变异氰酸酯/环氧树脂体系的化学计量比(I/E),采用FTIR/ATR、DSC、DMTA等研究了固化产物的结构与性能。结果表明,异氰酸酯与环氧树脂的固化历程随着温度的升高可分为三个阶段,第一阶段为异氰酸酯的三聚反应;第二阶段是一个复杂的过程,首先环氧树脂和异氰酸酯可反应生成嗯唑烷酮结构,通过嗯唑烷酮环扩链得到端畀氰酸酯基低聚物,可继续发生三聚反应;第三阶段为异氰脲酸酯与残余的环氧基团反应生成嗯唑烷酮结构,异氰脲酸酯六元环向噁唑烷酮五元环的转化是一个可逆的过程。不同的I/E比例可得到结构不同的固化物,不同的结构导致固化物性能的差异:当(I/E)=1.8时,综合力学性能良好,异氰酸酯/环氧树脂/玻璃纤维复合材料的弯曲强度、弯曲模量、层剪强度分别为652.53、33270.63和31.66MPa,优于甲基四氢苯酐/环氧树脂/玻璃纤维复合材料力学性能;当I/E=2.0时,固化物T_g达到了305℃,明显优于传统的环氧树脂固化体系。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.     

航空精密工件高精磨削的研究

零件在外圆磨床上加工时受两个力的作用,一是受零件磨削力的影响,二是受外圆磨床尾座对顶力的影响,尤其细长杆零件受力变形较为明显。为了在加工过程中避免零件变形而影响加工精度,通过使用ANSYS对零件进行有限元分析,控制两个方向力的大小,并对这两个方向力进行逐一分析,并配合高速磨削加工,确定进刀量、磨削速度、零件转速及对顶力等磨削参数,并对上述分析方法进行延伸扩展。